4 Important Things You Need to Know About Chamberlain Garage Door Openers

Chamberlain Garage Door Openers
image via rona.ca

In the sea of garage door openers in the market, Chamberlain is one of the most trusted and common brands out there. It is a worldwide brand that focuses on home control products.

If you are on the lookout for a garage door for your home, it is essential to know the ins and outs of every brand. You must weigh in the pros and cons, especially how the garage opener works to check if you are making the right investment.

Here are some of the aspects that you need to know about Chamberlain garage door openers.

How to Program and Install

Depending on the garage door opener that you choose, installation and programming may vary. A keyless entry system will have a different procedure from those using remote controls.

In a keyless entry system, the biometric technology is used to gain access. Before you install this system, unplug the opener first. Open the receiver with a screwdriver and twist up the cover. Remove 6 mm. of the insulation from each bell wire and connect each end to the screw terminals in the receiver. Let the wire pass along the channels to connect them. These terminals are labeled 2 and 1. Secure the wire between the opener and the receiver with insulated staples. The length of the wire will depend on where you will install your receiver. Opt for a polarized outlet for your receiver that is out of your children’s reach. Plug the receiver and the opener. Then, install the keyless entry by fastening it to a mounting surface. You can proceed to enrolling your first user. Open the cover to turn on the keyless entry and wait for the Enroll and Ready LED signs to light. Swipe the finger flat slowly until you get three passed swipes. After successful swipes, the Pass and Enroll LED will flash to signal that the enrollment is complete.

For remote controls, ensure that you already know where to find the Learn button on the garage door opener and the program button on your remote. Start with your remote first and hit the program button until the LED turns on. Then, proceed with the garage door opener and by pressing the learn button which will light up the LED. Within 30 seconds, press the button on your remote. Once successfully done, the light bulb will blink. Exit the programming mode by pressing any button except the programmed one. You can now test the remote by pressing the programmed button to check if it opens the garage door.

Common Problems and Troubleshooting

Once you’re already using your garage door opener, it is normal to encounter problems once in a while. Although you wouldn’t want to wish for problems for your new garage door opener, it is safe to know the simple troubleshooting for these common issues.

If the lights in your garage door turn off when it opens, you may need to adjust the force settings and travel. In addition to that, there may be obstructions that prevent the door from fully opening. To troubleshoot this problem, start by closing the door by pulling the release cord. Try to operate the system without using the door. If the light continues to turn off, reset the system by unplugging it for 30 seconds. Restore the power and activate the system. If you still encounter the same problem, disconnect the control wires from the opener and repeat opening and closing it. Your third option is to reset the force and travel adjustments. If the problem persists, you might need to replace your wall control and the wiring.

Special Features and Accessories

Your Chamberlain garage door opener comes with nifty features. Chamberlain belt drive openers are already quieter with the same power. Chain drive openers, on the other hand are more rugged and equipped with industrial strength for every climate. Most openers are already smartphone connected to allow you easy control whenever you’re away from home.

You can also purchase additional accessories that make your garage door opener the gadget for your home. With smartphone control products, you can easily access your security even if you’re away. You can control your garage door and lights through your smartphone. Wireless accessories are also available to enhance the communication in your home.

Chamberlain Tips and Tricks

In programming your Chamberlain garage door openers, here are some tips that you should keep in mind. When enrolling users on your keyless entry, ensure that your finger is clean and dry. Swipe it slowly and firmly by pushing it flat against the sensor.

To keep your garage secure and safe, keep your remote control out of children’s reach. Never allow your kids to operate the garage door opener remote. Remember to only open your garage door when it is in sight to avoid random people from entering your home.

Leave a Reply

Your email address will not be published. Required fields are marked *